1
KSh80.00

Cart

Quantity KSh80.00

Universal Network Cable Tester

(1 customer review)

KSh700.00

Universal  LAN tester

 Cat5 Cat6 UTP Phone LAN Wire Automatic Test Tool
Network Cable Tester RJ45 RJ11 Cat5 Cat6 UTP Phone LAN Wire Automatic Test Tool

A Network Cable Tester is a tester of network cables with twisted pair, straight and crossover wire configurations. Resolving network connectivity issues is often a mere process of elimination.

Main Function: Verify RJ11, RJ45 cables

Tracking Type : RJ11 & RJ45

Power: 9V Alkaline battery

Following are abnormal connections:
If one cable, for example, cable NO.3 is open-circuited, the two NO.3 lights of the main tester and remote tester will not turn on.
If several cables are not connected, several lights will not turn on respectively. If less than two cables are connected, none of the lights is on.

If two ends of a cable are disordered, for example, NO. 2and NO. 4, then displays on:
Main tester: 1-2-3-4-5-6-7-8-G
Remote tester: 1-4-3-2-5-6-7-8-G
If two cables are short-circuited, neither of the corresponding lights is on of the remote tester while the main tester remains unchanged.

If three cables, including three, are short-circuited, none of the corresponding lights is on.

If test patch panels or wall plate outlets, two cables that can match each other (RJ45) will be connected to the tester.

This network cable tester helps determine whether or not a network cable is the source of the problem. To use, connect one end of the network cable to the “Master” controller and the other end to the “Remote”.

Turn the switch found on the Master controller to the on position to begin testing. If the network cable is working properly, the Master controller and the Remote will illuminate sequentially with green lights.

When testing cables with RJ-11 connectors, lights 1 through 6 should illuminate. When testing cables with RJ-45 connectors, lights 1 through 8 should illuminate.

How to Test Your Ethernet Cables Using a Network Cable Connector.

The device is Super-simple to use!
1) Install a 9V battery
2) Connect your “test” cable to the appropriate jacks on the Main UNit and “Remote” unit
3) Turn it on. The RED “POWER” LED will start blinking: FAST in the “ON” position, SLOW in the “S” position
4) Watch the GREEN LEDs on the Main unit sequence from “1” to “G”, then repeat until you turn the Main unit OFF or disconnect the cable. Place the POWER switch in the “S” (Slow) position to better observe the LED sequencing.
5) The GREEN LEDs on the “Remote” unit will sequence with the Main unit’s LEDs, with the “Remote” LEDs indicating which wires are connected to each other.

IDEALLY, one ONE LED on each of the Main and “Remote” units will light in sequence. If NO LED on the “Remote” unit lights for a given Main unit LED, that wire IS NOT CONNECTED between the two points. READ THE INCLUDED DIRECTION SHEET to interpret other “LED ‘patterns, etc.'”

 

1 review for Universal Network Cable Tester

  1. tdk_shop

    Network Cable Tester RJ45 RJ11 RJ12 UTP LAN Cable Tester Networking Tool.
    I upgraded my 100Mbps Ethernet switch to a Gigabit model. But I was still only getting 100Mbps speeds. So I ordered the Zoostliss Network Cable Tester to help me troubleshoot the problem.

    I unpacked it from the box, ignored the instructions, and went to work. Within a few minutes, I found a poorly punched-down wire on a CAT5e jack, as well as a bad CAT6 patch cable. Painless to use and what a time saver!

    Operation is easy. Install a 9V battery. Next, attach the main scanner on one end of the RJ45 equipped cable and plug the remote module on the cable’s other end. Watch the LED’s on either module as they “round-robin” rotate from 1-8. If a LED appears out-of-sequence then there is a wiring error

Add a review

Your email address will not be published. Required fields are marked *

1
KSh80.00

Cart

Quantity KSh80.00